Many carbon monoxide and smoke detectors come with a “Hush” feature, which will stop the beeping for 72 hours. To silence the beeping, press and hold the “Hush” or “Test” button. The system will chirp to let you know the command is accepted, and you will have 72 before it begins again.
While your smoke alarm sounds, pressing the hush button will silence the smoke alarm for approximately 10 minutes. The hush feature is typically used where an alarm has been triggered accidently. This provides time to clear the current environment of fumes that triggered the alarm without the alert tone sounding.
The "HUSH" feature has the capability to temporarily desensitize the smoke alarm circuit for approximately 7 minutes. This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. The smoke alarm is desensitized by pushing the "HUSH" button on the smoke alarm cover.
Take the smoke detector off its mounting bracket on the ceiling and disconnect the power cable plugged to the smoke detector. Take out its battery, then press the “Test” button holding it down for 15 seconds. An alarm will sound for a short time, then the alarm will silence.
Even after the battery has died, the detector maintains a residual charge that will keep the chirp going for at least seven days. To get the device to stop chirping once the battery has been removed, you must drain this residual charge by holding the test button for 15 seconds.
Most battery powered smoke detectors will beep for a minimum of 30 days before the battery dies. You'll know the battery is losing charge if you hear consistent beeping every 30 to 60 seconds.
The “Hush” feature can be used repeatedly until the air has been cleared of the condition causing the alarm. Pushing the Test/Hush button on the alarm will end the hush period.
If you have changed the batteries and tried the circuit breaker, but the beeping persists, you may need to try resetting the detector(s): Use the reset button: most smoke detectors have a red reset button. Hold the reset button down for approximately 15-20 seconds.
Clear Residual Charge to Stop the Chirp
Remove the alarm from your ceiling or wall. Open the cover and take out the battery. Press and hold the test button for 15-30 seconds. This will fully reset the smoke alarm and drain any charge left inside.
Low Battery – The alarm will chirp every 30-40 seconds (every 60 seconds for some alarms) for a minimum of seven days. Replace the battery when this occurs, then test your alarm.
Yes, house alarm systems work when there is no electricity as long as there is a backup power source. But you should keep in mind that even with a backup, there is still the potential for the power source to go out, and the house alarm will go off if the battery dies.
Consistent Chirping
If a smoke alarm is chirping consistently, one of the following may be the reason: The battery may need to be replaced. An alarm will chirp every 30 to 60 seconds for a minimum of seven days. With a "low battery" announcement, disconnect the unit and replace the batteries.
This battery characteristic can cause a smoke alarm to enter the low battery chirp mode when air temperatures drop. Most homes are the coolest between 2 a.m. and 6 a.m. That's why the alarm may sound a low-battery chirp in the middle of the night, and then stop when the home warms up a few degrees.
The only way to tell is to put your ear next to it and listen for the chirp. The smoke alarm, furnace alarm, or carbon monoxide alarm alarm is chirping every 30 seconds or so, but it's hard to tell which direction the sound is coming from.
Most systems will begin beeping or chirping as a result of a total power outage or failure to recharge the system backup battery. For many of our most popular systems, beeping alarms and low battery trouble beeps can be silenced by pressing the [OFF] or [#] buttons from the keypad.
Depending on the timeout settings, most modern house alarms will go off for an average of 20 minutes. However, lengths may vary for traditional systems. A homeowner, tenant, or keyholders ability to stop an alarm is limited by the constraints of complex traditional settings that may require manual disabling.
Many people consider it a difficult job to do. Most people ask themselves, “can I remove a hardwired smoke detector?” The answer is you can！ If you have to stop the hard-wired smoke detectors from beeping, you must unplug them from the clip and remove the battery.
It's time to change the battery
Low batteries are the most common reason smoke detectors beep or send a trouble signal to your security panel, when there is no smoke or fire. As the battery weakens, the device will beep regularly to let you know it's time to replace it.
Smoke detectors are an essential part of modern buildings — from skyscrapers to individual homes. But these devices only work if they're in good condition and working properly. A fire detector may start beeping or chirping for a number of reasons, including low batteries or a malfunction in the unit.