What does it mean? Answer. This is the power indicator light: First Alert and BRK alarms have a power indicator light to show you that your alarm is receiving power. Some alarms have a red or green light that blinks every few minutes, while other models blink rapidly or shine a solid light.
Mains powered smoke alarms are required to have a green “Power ON” LED indicator. This will light up when the alarm is connected to mains power. All smoke Alarms also have a red light that flashes momentarily every 40-60 seconds to visually indicate they are operating.
Your alarm manufacturer may have included a blinking red light to let you know it's time to test the alarm again. The Batteries are Low: Usually accompanied by a loud beep, a blinking red light could mean the batteries in the unit are low. Consider adding fresh batteries and running a test to make sure it's working.
The mains powered smoke alarms have a green indicator. Smoke Alarms have a red light that goes off every 40 to 60 seconds to tell you if they're working. When the smoke alarm is activated, the red light flashes continuously.
A solid green light on your smoke detector indicates that the device is on and operating normally.
Typically, a smoke alarm has a red and green light to allow you to understand the system is working properly. However, there are other models that will integrate a third light indicator to separate when a malfunction, power source, and a simple battery replacement might be needed.
Smoke detector shows steady green light – no alarm
Battery and electrical power smoke detectors will usually have a steady green light to let you know the detector has electrical power and is in working order.
As the battery in a smoke alarm gets weak, the smoke alarm will “chirp” about once a minute to let you know that the battery needs to be replaced. Note: Only the device with a low battery will chirp. The other interconnected alarms should be silent.
Maintain your alarms
A “chirping” sound means that it's time to change batteries. Because alarm sensors wear out, replace each alarm at least every 10 years. Also, alarms have labels showing when they were made. If you don't see a label, the alarm is old and must be replaced.
Press and hold the test button on the smoke detector. It can take a few seconds to begin, but a loud, ear-piercing siren should emanate from the smoke detector while the button is pressed. If the sound is weak or nonexistent, replace your batteries.
Smoke detector brands like First Alert and SimpliSafe have a flashing red light as a reminder that their devices are working properly. A fire safety device that flashes but is otherwise still can be unsettling — but don't worry. These blinking red lights mean your detector's fine.
The most likely reason smoke detectors go off unexpectedly is that people aren't changing the batteries in them often enough. In most sensors you might think of, the strength of the signal goes up when they detect what they're supposed to. Common causes of smoke detector false positives around the house.
If your smoke detector has a blinking red light that flashes every 10 seconds, it means that it is reacting from the after-effects of smoke and is in a temporary desensitized state. When the smoke is no longer heavy in the air, the smoke detector should silence its alarm and the red light will start blinking.
This battery characteristic can cause a smoke alarm to enter the low battery chirp mode when air temperatures drop. Most homes are the coolest between 2 a.m. and 6 a.m. That's why the alarm may sound a low-battery chirp in the middle of the night, and then stop when the home warms up a few degrees.
Lens Detection
After locating the smoke detectors that are candidates for a camera, visually inspect the smoke detector and look for a small black dot and pinhole openings that provide the lens with perspective and a visual window. Like any camera lens, it will reflect and have a distinct visual appearance.
The National Fire Protection Association (NFPA) recommends changing the batteries in your smoke alarm every 6 months.
The Ultralife 10 Year Smoke Detector Battery is the only 9V battery warranted to last 10 years. Alkaline batteries in smoke detectors have to be changed every year. With the Ultralife 10 Year Battery, state-of-the-art lithium technology keeps your life-saving detector energized for a full 10 years.
The hardwired smoke detectors attached to your home's electrical system have backup batteries to sound the alarm even if the power goes out. You do need to change the batteries when the unit indicates that they are low on power to ensure continuous protection from smoke and fires.
It's time to change the battery
Low batteries are the most common reason smoke detectors beep or send a trouble signal to your security panel, when there is no smoke or fire. As the battery weakens, the device will beep regularly to let you know it's time to replace it.
The smoke alarm is desensitized by pushing the Test/Hush button on the smoke alarm cover. If the smoke is not too dense, the alarm will silence immediately and the red LED blinks every 10 seconds. This indicates that the alarm is in a temporarily desensitized condition.
If your detector or alarm has a blinking or steady light with no audible alarm sound, this typically indicates that the unit is receiving power.
Dust, Dirt and Environmental Smoke
Dust and dirt that comes from activities like remodeling may set off your smoke alarms. To clean your smoke alarm, open it up carefully, and look inside for dust or dirt. Use a vacuum attachment or electronic aerosol cleaner to remove dust particles.
Some smoke alarms also double as carbon monoxide detectors. When it gets cold outside, it's normal for people to crank up the heat. Furnaces, space heaters, fireplaces — these are some solutions to warming up a home.