The "HUSH" feature has the capability to temporarily desensitize the smoke alarm circuit for approximately 7 minutes. This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. The smoke alarm is desensitized by pushing the "HUSH" button on the smoke alarm cover.
Many carbon monoxide and smoke detectors come with a “Hush” feature, which will stop the beeping for 72 hours. To silence the beeping, press and hold the “Hush” or “Test” button. The system will chirp to let you know the command is accepted, and you will have 72 before it begins again.
While your smoke alarm sounds, pressing the hush button will silence the smoke alarm for approximately 10 minutes. The hush feature is typically used where an alarm has been triggered accidently. This provides time to clear the current environment of fumes that triggered the alarm without the alert tone sounding.
In most cases, you can find the 'hush' button on the smoke detector's cover. However, if you have trouble finding the button or are not sure if your detector has the feature, check out your user manual.
First, try the reset button on each smoke alarm. If that doesn't work, flipping the circuit breaker off and back on might stop the noise. If all of that fails, your ultimate solution may be to disconnect the smoke alarms and remove their batteries one by one.
This battery characteristic can cause a smoke alarm to enter the low battery chirp mode when air temperatures drop. Most homes are the coolest between 2 a.m. and 6 a.m. That's why the alarm may sound a low-battery chirp in the middle of the night, and then stop when the home warms up a few degrees.
To fix your smoke alarm from chirping pointlessly, first discharge the device, use the hush button, and reconnect all the cables. Next, you can try resetting the circuit breaker and your smoke alarm as well.
Removing the battery from your smoke alarm won't set it off. It kills the power to the alarm and renders it useless, so you should only remove the battery when you're replacing it with a new one.
Newer smoke alarms keep some errors in the processor. The smoke alarm must clear errors after the battery is changed, but it might continue to chirp even after you change the batteries. This usually occurs in electrical powered smoke alarms with a battery backup.
Even after the battery has died, the detector maintains a residual charge that will keep the chirp going for at least seven days. To get the device to stop chirping once the battery has been removed, you must drain this residual charge by holding the test button for 15 seconds.
Most hard-wired smoke detectors use a 9-volt battery that is supposed to kick in if your home loses electricity. When that battery is running low, your detector alerts you with a chirp that it's running low. Replacing the battery solves the problem.
Try a manual reset.
Remove the batteries and hold down the reset button for 15 to 20 seconds. Reconnect the batteries and alarm. It will most likely beep once as evidence it is working, then it should stop.
The "HUSH" feature has the capability to temporarily desensitize the smoke alarm circuit for approximately 7 minutes. This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. The smoke alarm is desensitized by pushing the "HUSH" button on the smoke alarm cover.
Most people don't change the batteries in their smoke detectors often enough and that's the most likely reason why they go off unexpectedly.
Your alarm manufacturer may have included a blinking red light to let you know it's time to test the alarm again. The Batteries are Low: Usually accompanied by a loud beep, a blinking red light could mean the batteries in the unit are low. Consider adding fresh batteries and running a test to make sure it's working.
Chirping every 30-40 seconds is generally an indication that the battery is running low. If your smoke or heat alarm has a replaceable battery, try replacing the battery with a brand new one. It is recommended to change the batteries in your smoke and heat alarms every 12 months.
Many people consider it a difficult job to do. Most people ask themselves, “can I remove a hardwired smoke detector?” The answer is you can！ If you have to stop the hard-wired smoke detectors from beeping, you must unplug them from the clip and remove the battery.
Hardwired smoke detectors (which typically include a backup battery) are subject to similar issues as those that operate on a battery only. However, hardwired units often require resetting after problems are addressed. On most, simply hold the reset button for 15 to 20 seconds to silence the noise.
If your First Alert smoke alarm beeps 3 times after a new battery is installed, try replacing the battery first. If the issue persists, check to make sure that the battery drawer is sliding in and out easily and completely.
Power interruptions are common in areas where utility companies switch grids in the early hours of the morning. In AC or AC/DC smoke alarms, a loose hot wire connection can also disconnect power to the smoke alarm. The effect is the same as a power failure. When power is restored, the units may alarm briefly.